EXACTLY HOW TO INSTALL A BATH TUB YOURSELF

Exactly How to Install a Bath Tub Yourself

Exactly How to Install a Bath Tub Yourself

Blog Article

Detail

This great article below relating to A Step-by-Step Guide to Installing a Bathtub is indeed compelling. Give it a go and make your own conclusions.


Installing A Bathtub
Installing a bathtub isn't exactly rocket science, but it does require solid plumbing, carpentry, and also occasionally, tiling skills. Replacing an old bathtub with a brand-new one is additionally a reasonably tough job. If the old tub is easily available, the project can move speedily; if you need to open a wall to get rid of the old bathtub and also place the new bathtub, the task is a lot harder. In either instance, the job is within a house handyman's skills, although you will certainly need a helper to vacate the old bathtub and embeded in the brand-new one. Make certain you have qualified on your own for the work as well as are comfortable attempting it. Instead of hiring a contractor to take control of a halfway-completed job, it is better to consider using one prior to you begin. Chances are you might need a professional plumber to make tube connections.
This short article will certainly assist you set up a new bath tub in your restroom if you have currently gotten a new bathtub as well as don't require to alter the arrangement of your previous water pipes.
Your devices as well as material list ought to comprise the following:
  • New Tub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Knife

  • Measuring tape

  • Pipe Caps


  • Removing Old Touches


    If you need to change old taps with new ones as a part of your installation, after that the first thing you must do is disconnect the water. After doing so, turn on the faucets to drain any kind of water staying in the system. The process of eliminating the existing taps can be fairly problematic because of the restricted gain access to that is frequently the instance.
    Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the faucets. Have a fabric all set for the remaining water that will certainly come from the pipelines. Once the supply pipes have been gotten rid of, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the solitary taps from transforming during this process. When the taps have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any old sealing substance.
    Before going on to fit the new faucets, compare the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is needed for the new faucets to fit.

    Suitable New Taps


    If the tails of the brand-new taps are plastic, after that you will certainly need a plastic port to prevent damage to the string. One end of the connector fits on the plastic tail of the faucet and also the other end supplies a connection to the existing supply pipes.
    If you require to fit a monobloc, then you will call for reducing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
    Next, place the faucet in the mounting opening in the bath/basin ensuring that the washers remain in area between the tap and also the sink. Safeguard the tap in place with the supplier given backnut. Once the tap is firmly in position, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with normal faucet adapters. The former type must be attached to the faucet ends first, tightening just by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have been linked.

    Mounting the Bath tub


    Using the two wooden boards under its feet, put the bathtub in the called for placement. The wooden boards are useful in uniformly spreading out the weight of the bathtub over the area of the boards rather than focusing all the weight onto four tiny factors.
    The next goal is to ensure that the bathtub is leveled all round. This can be accomplished by inspecting the spirit level as well as changing the feet on the tub up until the level reviews degree.
    To mount faucets, fit all-time low of the furthest adaptable faucet connector to the suitable supply pipe by making a compression join; then do the exact same for the various other faucet.
    Activate the water and also examine all joints and also brand-new pipework for leaks and tighten them if necessary. Fill the tub and likewise inspect the overflow outlet as well as the typical electrical outlet for leakages.
    Ultimately, deal with the bathroom paneling as defined in the producer's instruction manual. Tiling and sealing around the bathtub should wait until the bathtub has been used at least when as this will certainly settle it into its final placement.

    Planning for the Installment


    To start with, the supporting frame provided with the bathroom ought to be fitted (if required) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is necessary to see to it that if the faucet includes a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets system to prevent strain on the bath tub.
    Fit the versatile tap connectors to the bottom of both faucets using 2 nuts and also olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next off, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make certain you utilize all of the provided washers.
    Link the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom ought to now prepare to be fitted in its last position.

    Tiling Around the Bath tub


    In the area where the bathroom satisfies the tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to break a stiff seal, causing the water to permeate the wall between the bathroom and the tiling, leading to issues with dampness and also possible leakages to the ceiling below.
    You can select from a selection of coloured sealants to assimilate your fixtures as well as fittings. They are marketed in tubes as well as cartridges, and can sealing spaces up to a size of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill the bathtub with water prior to sealing, to enable the movement experienced when the bathtub is in use. The sealer can break rather early if you do not take into account this motion prior to securing.
    Additionally, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise quickly available on the market. It is suggested to fit the tiles utilizing water-resistant or water-proof adhesive as well as cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    Installing A Bathtub

    I hope you liked our part about How to Install a Bathtub. Thanks a lot for taking time to read our article post. Sharing is nice. Who knows, you may be helping someone out. We thank you for reading our article about How to Install a Bathtub.




    Free Quote


    Report this page